The Effects of Partial Replacement of Ground Granulated Blast Furnace Slag by Ground Wood Ash on Alkali-Activated Binder Systems.

Cement production contributes significantly to carbon dioxide emissions. Alkali-activated materials offer an environmentally friendly alternative due to their comparable strength, durability and low-carbon emissions while utilizing wastes and industrial by-products. Wood ash is a waste material that shows promising results as a partial replacement for Portland cement and precursors in alkali-activated systems. The aim of this study was to examine the effect of ground wood ash on the mechanical properties of alkali-activated mortars. Wood ash was incorporated as a 0 wt%, 10 wt% and 20 wt% partial replacement for ground granulated blast furnace slag (GGBFS). The wood ashes were ground in a planetary ball mill for 10 and 20 min. Sodium silicate (Na2SiO3), sodium carbonate (Na2CO3), and sodium hydroxide (NaOH) were used as alkali activators. The results demonstrated that ground wood ash improved the mechanical properties of alkali-activated systems compared to untreated wood ash. However, the incorporation of wood ash increased the porosity of the binder matrix.

Eco-Concrete in High Temperatures.

Concrete technology is becoming more and more sustainable and ecological following more extensive and focused research. The usage of industrial waste and by-products, such as steel ground granulated blast-furnace slag (GGBFS), mine tailing, fly ash, and recycled fibers, is a very important step toward a good transition of concrete into a "green" future and significant improvement in waste management in the world. However, there are also several known durability-related problems with some types of eco-concretes, including exposure to fire. The general mechanism occurring in fire and high-temperature scenarios is broadly known. There are many variables that weightily influence the performance of this material. This literature review has gathered information and results regarding more sustainable and fire-resistant binders, fire-resistant aggregates, and testing methods. Mixes that utilize industrial waste as a total or partial cement replacement have been consistently achieving favorable and frequently superior outcomes when compared to conventional ordinary Portland cement (OPC)-based mixes, especially at a temperature exposure up to 400 °C. However, the primary emphasis is placed on examining the impact of the matrix components, with less attention given to other factors such as sample treatment during and following exposure to high temperatures. Furthermore, there is a shortage of established standards that could be utilized in small-scale testing.

Wood Ash as Sustainable Alternative Raw Material for the Production of Concrete-A Review.

Different ecological binders have been used to minimize the negative effects of cement production and use on the environment. Wood ash is one of these alternative binders, and there has been increasing research related to this topic recently. The wood ash utilized in the literature primarily originates from power plants and local bakeries, and predominantly wood fly ash is used. This review paper examines the use of wood ash as an ecological binder in two different applications: as a cement replacement and as an alkali-activated material. Studies have shown that while increased wood ash content in concrete and mortars can have negative effects on strength and durability, it is still a promising and developable material. Depending on the chemical composition of the wood ash, the strength and durability properties of concrete might be slightly improved by utilizing wood ash as a replacement for cement, with an optimal replacement level of 10-20%. However, there is a need for more research regarding the effects of wood ash on the durability of cement-based materials and its use in alkali-activated materials. Overall, this review provides a comprehensive overview of the properties of wood ash and its potential applications in conventional concrete and mortars, as well as in alkali-activated materials.

Interpretable Machine Learning for Prediction of Post-Fire Self-Healing of Concrete.

Developing accurate and interpretable models to forecast concrete's self-healing behavior is of interest to material engineers, scientists, and civil engineering contractors. Machine learning (ML) and artificial intelligence are powerful tools that allow constructing high-precision predictions, yet often considered "black box" methods due to their complexity. Those approaches are commonly used for the modeling of mechanical properties of concrete with exceptional accuracy; however, there are few studies dealing with the application of ML for the self-healing of cementitious materials. This paper proposes a pioneering study on the utilization of ML for predicting post-fire self-healing of concrete. A large database is constructed based on the literature studies. Twelve input variables are analyzed: w/c, age of concrete, amount of cement, fine aggregate, coarse aggregate, peak loading temperature, duration of peak loading temperature, cooling regime, duration of cooling, curing regime, duration of curing, and specimen volume. The output of the model is the compressive strength recovery, being one of the self-healing efficiency indicators. Four ML methods are optimized and compared based on their performance error: Support Vector Machines (SVM), Regression Trees (RT), Artificial Neural Networks (ANN), and Ensemble of Regression Trees (ET). Monte Carlo analysis is conducted to verify the stability of the selected model. All ML approaches demonstrate satisfying precision, twice as good as linear regression. The ET model is found to be the most optimal with the highest prediction accuracy and sufficient robustness. Model interpretation is performed using Partial Dependence Plots and Individual Conditional Expectation Plots. Temperature, curing regime, and amounts of aggregates are identified as the most significant predictors.

The Impact of Different Parameters on the Formwork Pressure Exerted by Self-Compacting Concrete.

Despite the advantageous benefits offered by self-compacting concrete, its uses are still limited due to the high pressure exerted on the formwork. Different parameters, such as those related to concrete mix design, the properties of newly poured concrete, and placement method, have an impact on form pressure. The question remains unanswered on the degree of the impact for each parameter. Therefore, this study aims to study the level of impact of these parameters, including slump flow, T500 time, fresh concrete density, air content, static yield stress, concrete setting time, and concrete temperature. To mimic the casting scenario, 2 m columns were cast at various casting rates and a laboratory setup was developed. A pressure system that can wirelessly and continuously record pressure was used to monitor the pressure. Each parameter's impact on the level of pressure was examined separately. Casting rate and slump flow were shown to have a greater influence on pressure. The results also demonstrated that, while higher thixotropy causes form pressure to rapidly decrease, a high casting rate and high slump flow lead to high pressure. This study suggests that more thorough analysis should be conducted of additional factors that may have an impact, such as the placement method, which was not included in this publication.

Hybrid Interfacial Transition Zone between Wet-On-Wet Casted Concrete-Microstructure and Mechanical Properties.

The manufacture of elements containing two types of concrete allows for the minimization of the amount of Portland cement by matching the properties of concrete with local structural and durability requirements. The most common production method of the hybrid element is wet-on-hard and wet-on-wet. Casting wet-on-dry is the most common approach while casting wet-on-wet has been used mostly for concrete overlays and screeds. The study focuses on the wet-on-wet method but is applied in the production of vertical and horizontal elements. Bond-behavior and micro properties of the wet-on-wet casting interface of ultra-high-performance concrete (UHPC)-normal strength concretes are investigated. The obtained results indicate the formation of a hybrid interfacial transition zone between the two types of casted concrete. The binder matrix located in this zone appeared to combine properties of both used concrete. Porosity, phase composition, and presumably also strength, changed gradually. Furthermore, despite significant differences in shrinkage, no microcracking or delamination was observed in that zone. The ultimate flexural and compressive strength of the produced elements were either equal to the stronger concrete or were higher than the weaker of the used concrete.

Strength Characteristics of Alkali-Activated Slag Mortars with the Addition of PET Flakes.

The production of ordinary Portland cement is associated with significant CO2 emissions. To limit these emissions, new binders are needed that can be efficiently substituted for cement. Alkali-activated slag composites are one such possible binder solution. The research programme presented herein focused on the creation of alkali-activated slag composites with the addition of PET flakes as a partial substitute (5%) for natural aggregate. Such composites have a significantly lower impact in terms of CO2 emissions in comparison to ordinary concrete. The created composites were differentiated by the amount of activator (10 and 20 wt.%) and curing temperature (from 20 to 80 °C). Their mechanical properties were tested, and a scanning electron microscope analysis was conducted. Compressive and flexural strengths ranging from 29.3 to 68.4 MPa and from 3.5 to 6.1 MPa, respectively, were achieved. The mechanical test results confirmed that a higher amount of activator improved the mechanical properties. However, the influence of the PET particles on the mechanical properties and microstructure varied with the curing temperature and amount of activator. Areas that require further research were identified.

Lateral Formwork Pressure for Self-Compacting Concrete-A Review of Prediction Models and Monitoring Technologies.

The maximum amount of lateral formwork pressure exerted by self-compacting concrete is essential to design a technically correct, cost-effective, safe, and robust formwork. A common practice of designing formwork is primarily based on using the hydrostatic pressure. However, several studies have proven that the maximum pressure is lower, thus potentially enabling a reduction in the cost of formwork by, for example, optimizing the casting rate. This article reviews the current knowledge regarding formwork pressure, parameters affecting the maximum pressure, prediction models, monitoring technologies and test setups. The currently used pressure predicting models require further improvement to consider several pressures influencing parameters, including parameters related to fresh and mature material properties, mix design and casting methods. This study found that the maximum pressure is significantly affected by the concretes' structural build-up at rest, which depends on concrete rheology, temperature, hydration rate and setting time. The review indicates a need for more in-depth studies.

Novel humidity sensors based on nanomodified Portland cement.

Commonly used humidity sensors are based on metal oxides, polymers or carbon. Their sensing accuracy often deteriorates with time, especially when exposed to higher temperatures or very high humidity. An alternative solution based on the utilization of Portland cement-based mortars containing in-situ grown carbon nanofibers (CNFs) was evaluated in this study. The relationship between the electrical resistivity, CNF content and humidity were determined. The highest sensitivity was observed for samples containing 10 wt.% of the nanomodified cement which corresponded to 0.27 wt.% of CNFs. The highest calculated sensitivity was approximately 0.01024 per 1% change in relative humidity (RH). The measured electrical resistivity is a linear function of the RH in the humidity range between 11 and 97%. The percolation threshold value was estimated to be at around 7 wt.% of the nanomodified cement, corresponding to ~ 0.19 wt.% of CNFs.

Eco-UHPC as Repair Material-Bond Strength, Interfacial Transition Zone and Effects of Formwork Type.

A reduced carbon footprint and longer service life of structures are major aspects of circular economy with respect to civil engineering. The aim of the research was to evaluate the interfacial bond properties between a deteriorated normal strength concrete structure and a thin overlay made of Eco-UHPC containing 50 wt% of limestone filler. Two types of formwork were used: untreated rough plywood and surface treated shuttering plywood. The normal strength concrete elements were surface scaled using water jets to obtain some degradation prior to casting of the UHPC overlay. Ultrasonic pulse velocity (UPV), bond test (pull-off test), and Scanning Electron Microscopy (SEM) combined with Energy Dispersive Spectrometry (EDS) were used for analysis. Elements repaired with the Eco-UHPC showed significantly improved mechanical properties compared to the non-deteriorated NSC sample which was used as a reference. The bond strength varied between 2 and 2.7 MPa regardless of the used formwork. The interfacial transition zone was very narrow with only slightly increased porosity. The untreated plywood, having a rough and water-absorbing surface, created a surface friction-based restraint which limited microcracking due to autogenous shrinkage. Shuttering plywood with a smooth surface enabled the development of higher tensile stress on the UHPC surface, which led to a more intensive autogenous shrinkage cracking. None of the formed microcracks penetrated through the entire thickness of the overlay and some were partly self-healed when a simple water treatment was applied. The project results showed that application of UHPC as repair material for concrete structures could elongate the lifespan and thus enhance the sustainability.

A Review of the Mechanical Properties and Durability of Ecological Concretes in a Cold Climate in Comparison to Standard Ordinary Portland Cement-Based Concrete.

Most of the currently used concretes are based on ordinary Portland cement (OPC) which results in a high carbon dioxide footprint and thus has a negative environmental impact. Replacing OPCs, partially or fully by ecological binders, i.e., supplementary cementitious materials (SCMs) or alternative binders, aims to decrease the carbon dioxide footprint. Both solutions introduced a number of technological problems, including their performance, when exposed to low, subfreezing temperatures during casting operations and the hardening stage. This review indicates that the present knowledge enables the production of OPC-based concretes at temperatures as low as -10 °C, without the need of any additional measures such as, e.g., heating. Conversely, composite cements containing SCMs or alkali-activated binders (AACs) showed mixed performances, ranging from inferior to superior in comparison with OPC. Most concretes based on composite cements require pre/post heat curing or only a short exposure to sub-zero temperatures. At the same time, certain alkali-activated systems performed very well even at -20 °C without the need for additional curing. Chemical admixtures developed for OPC do not always perform well in other binder systems. This review showed that there is only a limited knowledge on how chemical admixtures work in ecological concretes at low temperatures and how to accelerate the hydration rate of composite cements containing high amounts of SCMs or AACs, when these are cured at subfreezing temperatures.

Geopolymer Based on Mechanically Activated Air-cooled Blast Furnace Slag.

An efficient solution to increase the sustainability of building materials is to replace Portland cement with alkali-activated materials (AAM). Precursors for those systems are often based on water-cooled ground granulated blast furnace slags (GGBFS). Quenching of blast furnace slag can be done also by air but in that case, the final product is crystalline and with a very low reactivity. The present study aimed to evaluate the cementitious properties of a mechanically activated (MCA) air-cooled blast furnace slag (ACBFS) used as a precursor in sodium silicate alkali-activated systems. The unreactive ACBFS was processed in a planetary ball mill and its cementing performances were compared with an alkali-activated water-cooled GGBFS. Mixes based on mechanically activated ACBFS reached the 7-days compressive strength of 35 MPa and the 28-days compressive strength 45 MPa. The GGBFS-based samples showed generally higher compressive strength values.

The Effect of Exposure on the Autogenous Self-Healing of Ordinary Portland Cement Mortars.

Exposure conditions are critical for the autogenous self-healing process of Portland cement based binder matrixes. However, there is still a significant lack of fundamental knowledge related to this factor. The aim of this paper was to investigate and understand the effects of various potentially applicable curing solutions on the efficiency of the crack closure occurring both superficially and internally. Four groups of exposures were tested, including exposure with different water immersion regimes, variable temperatures, application of chemical admixtures, and use of solutions containing micro particles. The self-healing process was evaluated externally, at the surface of the crack, and internally, at different crack depths with the use of optical and scanning electron microscopes (SEM). The phase identification was done with an energy dispersive spectrometer combined with the SEM. The results showed very limited self-healing in all pure water-based exposures, despite the application of different cycles, temperatures, and water volumes. The addition of a phosphate-based retarding admixture demonstrated the highest crack closure, both internally and externally. The highest strength recovery and a very good crack closure ratio was achieved in water exposure containing micro silica particles. The main phase observed on the surface was calcium carbonate, and internally, calcium silicate hydrate, calcium carbonate, and calcium phosphate compounds. Phosphate ions were found to contribute to the filling of the crack, most likely by preventing the formation of a dense shell composed of hydration phases on the exposed areas by crack unhydrated cement grains as well as by the additional precipitation of calcium and phosphate-based compounds. The micro sized silica particles presumably served as nucleation sites for the self-healing products growth. Changes in the chemical composition of the self-healing material were observed with a distance from the surface of the specimen.

Does a High Amount of Unhydrated Portland Cement Ensure an Effective Autogenous Self-Healing of Mortar?

It is commonly accepted that the autogenous self-healing of concrete is mainly controlled by the hydration of Portland cement and its extent depends on the availability of anhydrous particles. High-performance (HPCs) and ultra-high performance concretes (UHPCs) incorporating very high amounts of cement and having a low water-to-cement ratio reach the hydration degree of only 70-50%. Consequently, the presence of a large amount of unhydrated cement should result in excellent autogenous self-healing. The main aim of this study was to examine whether this commonly accepted hypothesis was correct. The study included tests performed on UHPC and mortars with a low water-to-cement ratio and high cement content. Additionally, aging effects were verified on 12-month-old UHPC samples. Analysis was conducted on the crack surfaces and inside of the cracks. The results strongly indicated that the formation of a dense microstructure and rapidly hydrating, freshly exposed anhydrous cement particles could significantly limit or even hinder the self-healing process. The availability of anhydrous cement appeared not to guarantee development of a highly effective healing process.

Effects of Fineness and Chemical Composition of Blast Furnace Slag on Properties of Alkali-Activated Binder.

The effects of fines and chemical composition of three types of ground granulated blast furnace slag (GGBFS) on various concrete properties were studied. Those studied were alkali activated by liquid sodium silicate (SS) and sodium carbonate (SC). Flowability, setting times, compressive strength, efflorescence, and carbonation resistance and shrinkage were tested. The chemical composition and microstructure of the solidified matrixes were studied by X-ray diffraction (XRD), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) coupled with EDX analyser. The results showed that the particle size distribution of the slags and the activator type had significantly stronger effects on all measured properties than their chemical composition. The highest compressive strength values were obtained for the finest slag, which having also the lowest MgO content. SC-activated mortar produced nearly the same compressive strength values independently of the used slag. The most intensive efflorescence and the lowest carbonation resistance developed on mortars based on slag containing 12% of MgO and the lowest fineness. The slag with the highest specific surface area and the lowest MgO content developed a homogenous microstructure, highest reaction temperature and lowest drying shrinkage. Thermogravimetric analysis indicated the presence of C-(A)-S-H, hydrotalcite HT, and carbonate like-phases in all studied mortars.

Piezoresistive Load Sensing and Percolation Phenomena in Portland Cement Composite Modified with In-Situ Synthesized Carbon Nanofibers.

Carbon nanofibers (CNFs) were directly synthesized on Portland cement particles by chemical vapor deposition. The so-produced cements contained between 2.51-2.71 wt% of CNFs; depending on the production batch. Several mortar mixes containing between 0 and 10 wt% of the modified cement were produced and the electrical properties at various ages and the load sensing capabilities determined. The percolation threshold related to the electrical conductivity was detected and corresponded to the amount of the present CNFs, 0.271, 0.189, 0.135 and 0.108 wt%. The observed threshold depended on the degree of hydration of the Portland cement. The studied mortars showed a strong piezoresistive response to the applied compressive load reaching a 17% change of the electrical resistivity at an applied load of 3.5 MPa and 90% at 26 MPa. This initial study showed that the studied material is potentially suitable for future development of novel fully integrated monitoring systems for concrete structures.

Activation of a Raw Clay by Mechanochemical Process-Effects of Various Parameters on the Process Efficiency and Cementitious Properties.

The efficiency of the mechanochemical activation (MCA) is influenced by various process parameters as well as by the properties of the treated material. The main objective of this research was to optimize the MCA process, gaining enhancement of the chemical reactivity of a Swedish raw clay, which is going to be used as an alkali-activated cementitious binder. The effects of the amount of water, the filling ratio, the rotation speed, and the grinding duration on the amorphization degree were evaluated by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). Generally, wet and dry processes showed an extensive amorphization of both kaolinite and muscovite minerals present in the studied clay. On the contrary, quartz was amorphized mainly by the wet grinding process. The efficiency of both dry and wet grinding processes was enhanced by the increased number of grinding media versus the amount of the activated material. However, longer processing times caused significant agglomeration while a higher rotational speed enhanced the amorphization. Preliminary tests have shown that alkali activation of the processed clays produced hardened samples. Furthermore, the increased amorphization corresponded to the increased compressive strength values.

Formation of Lignin Nanoparticles by Combining Organosolv Pretreatment of Birch Biomass and Homogenization Processes.

Valorization of lignocellulosic biomass into a biorefinery scheme requires the use of all biomass components; in this, the lignin fraction is often underutilized. Conversion of lignin to nanoparticles is an attractive solution. Here, we investigated the effect of different lignin isolation processes and a post-treatment homogenization step on particle formation. Lignin was isolated from birch chips by using two organosolv processes, traditional organosolv (OS) and hybrid organosolv-steam explosion (HOS-SE) at various ethanol contents. For post-treatment, lignin was homogenized at 500 bar using different ethanol:water ratios. Isolation of lignin with OS resulted in unshaped lignin particles, whereas after HOS-SE, lignin micro-particles were formed directly. Addition of an acidic catalyst during HOS-SE had a negative impact on the particle formation, and the optimal ethanol content was 50⁻60% v/v. Homogenization had a positive effect as it transformed initially unshaped lignin into spherical nanoparticles and reduced the size of the micro-particles isolated by HOS-SE. Ethanol content during homogenization affected the size of the particles, with the optimal results obtained at 75% v/v. We demonstrate that organosolv lignin can be used as an excellent starting material for nanoparticle preparation, with a simple method without the need for extensive chemical modification. It was also demonstrated that tuning of the operational parameters results in nanoparticles of smaller size and with better size homogeneity.